Our family has been seeing Dr. Asarkof since we moved to Concord nearly twenty years ago. He is a great dentist who also shares my interest in woodworking. One of the things he does in his spare time to relax is slicing logs into thick slabs. When he learned that we were hoping to make our foyer bench out of a live edge slab he invited us to his home to have a look at his collection. We picked out a lovely piece of cherry and one of hard maple which he gifted to us. When we returned to the River House, Jeanine and I worked together on applying finish to a bunch of cabinet parts which took us until dinner time. I then started to work on the slab. It had a significant twist so I made a sled so I could run it through my planer. I used every last bit of the 16″ capacity and it made all the work of moving the behemoth into my shop worth it. Then next challenge that I tackled this morning, was figuring out how to install it. The cavity where it resides has a longer back than front dimension. That means if you size the board to slide in from the front then you will have a big gap in the sides at the back. Because the slab is so thick, rotating into place won’t work either because the front face diagonal is longer the the width of the opening. To solve this problem I did a back bevel on all but the first 1/4″ of the right side. This provided the clearance to rotate while leaving enough material on the face to have a flush fit. I am very pleased with the result and from hereforth, this will be called Keith’s bench in honor of our dentist.
As someone who primarily works alone, I have come to rely on a number of tools without which it is hard to imagine how I could get anything done. One such tool is the adjustable jack stand shown here providing temporary support for a wall-hung cabinet in my future office. One is being used to support the weight while the other is keeping the cabinet pressed against the wall. The laser level is another indispensable tool. With this setup, I am able to leisurely set my shims to square everything up and then drive the hanging fasteners without having to worry about anything else.
Despite having a rather large collection of clamps, occasionally I am faced with a situation where none of them will do the job. As pictured above, I used some salvaged lumber to fashion an expansion clamp so that I could secure a piece of wall trim to the cabinet frame. I added two more after exiting the pantry so as not to trap myself inside. As of today, I am done with all the casework for the four bathrooms, laundry, kitchen, and pantry. I feel good about where things stand but have much more work ahead. Our plans include built-in cabinetry in the living room, both offices, the mudroom, the foyer, and two walk-in closets. Let’s not forget all the drawers and doors that are needed or the 29 stair treads. I think it is safe to say I will not be running out of work anytime soon.
Kyle recently purchased a Traeger wood pellet smoker and decided to grill a pork shoulder and vegetables this afternoon. He shared this photo with the family. I have several things to say about this. (1) Kyle is definitely his mother’s son and I am sure she is thrilled to see him developing skills as a cook (a statement that applies equally to his siblings). (2) If he sends this photo to my brother, he can expect to spend an hour on the phone learning all the finer points of smoking meat. (3) It is possible his family will heretofore refer to him as Meat Boy, since this was the label used on the iPhone app he uses to monitor the status of the smoker. (4) This seems like a lot of food for one person so I am guessing the meal may have been prepared for the benefit of a date. (5) I am free for lunch tomorrow as I understand there are plenty of leftovers.
The kitchen in our new house includes a walk-in pantry. On one side there are base and wall cabinets, an area for a flush-mount integrated freezer, and a nook for storing a step ladder and broom. Today, I completed an entire wall of open shelving located on the other side. Surprisingly, these built-ins took significantly longer to build than much of the cabinetry. The shelves are each 1-1/2 inches thick, 8 inches deep and 8 feet long weighing 25 pounds a piece. Their size and weight made it necessary to construct the assembly in place. The biggest challenge was to come up with a design that would support the anticipated shelf loading and to do so without any visible fasteners. Key to both of these are the short vertical supports. Each one conceals within its width a 3-1/2 inch pocket hole screw that secures the shelf to a 2×4 behind the wall, a biscuit joint that locates and secures the vertical support to the shelf, and a recessed screw that captures the vertical support below. Not visible is a horizontal cleat that supports the bottom shelf from below. Now that I see the shelving installed, I may go back and cut off the portion of the end supports that go down to the floor. They are not necessary to support the shelves and I feel like they diminish the visual appeal of the otherwise cantilevered design.
UPDATE: I removed the “legs” as planned and am much happier with the appearance.
Maya decided that she needed to get back on the horse, or rather a mountain bike, since the crash that badly injured her shoulder. It was meant to be a way of moving past any lingering fear she might be harboring since the traumatic event. Instead, she sustained an equally serious injury to her other shoulder and a nice set of bruises as well. Her brothers and parents who all gathered today for lunch at the Road House suggested to her that maybe mountain biking was not a good sport for her. On the bright side, she reports that she already knows all the right specialists to see and has satisfied her medical insurance deductible. I am beginning to regret the “brave Maya” training I did with her when she was a small child. She has turned out to be quite fearless but it remains to be seen what she learns from her injuries.
Here is some fatherly wisdom that may apply to this situation: If at first you don’t succeed then skydiving may not be for you.
I am belatedly memorializing a delicious meal that Jeanine prepared earlier this week. Since she rarely makes the same dish twice in a year, I am saving this image to suggest that this is one worth repeating on a more frequent basis.
Today’s River House project was the installation of the island vent hood. The work was fairly straightforward with the most time spent ensuring that the vent was perfectly plumb and sealing the ductwork. I got a good upper body workout as it was necessary to hold a number of different components overhead while screwing them into place. Once installed, I had to open up the controller board and set a jumper to limit the maximum fan speed to 390 cfm. If you go over 400 cfm then you have to install a make-up air system which is something we do not need and didn’t want to be forced into. The hanging blue tape is to keep taller folks from running into the glass canopy before the island is installed. As it stands, I can just walk under it without banging my head.
Our double oven was delivered today. Of all the components going into our new home, it had the longest lead time of more than a year. As if to ensure it was here to stay, I immediately installed it, a task easier said than done given its weight of 333 pounds. Working alone forces you to always have an approach that does not rely on brute force. In this case, I built a temporary platform out of scrap lumber so that I could slide the oven directly into its opening. None of the cabinetry I have built has more demanding tolerances than the one for the double oven. It has to be dead plumb, dead level, and perfectly square in all orientations. If any one of these attributes is off by even the slightest amount, it will show up as a problem with the installation. I am happy to report that the time I spent making sure that the cabinet was just right resulted in a perfect fit. Also operational now is our microwave. We debated for some time if we should even have one in the kitchen. The new oven has a steam heating feature which is the healthiest way to reheat foods, the primary task which we have used the microwave for in the past. In the end, we decided a microwave would be convenient but need not be large and we wanted it to be located for convenient use. Our Road House has an under counter unit with automated drawer, a perfect solution for three foot tall people but a terrible location for anyone taller.
The bamboo plywood I am using is constructed of three plys. The front and back are 1/8″ thick vertically oriented laminations. The core is 1/2″ thick with laminations that run perpendicular. Whenever I need edge facing, I cut the top and bottom layers off leaving the core as waste. Having saved up all of these half-inch strips, I glued them together to create an end-grain cutting board. Jeanine liked it so much that she wanted me to make an entire bench top using this technique. It is a great idea but would represent a very time-consuming effort and perhaps one I could tackle well after we have moved in.
Precordial catch syndrome (PCS) is a non-serious condition in which there are sharp stabbing painsinthechest. These typically get worse with inhaling and occur within a small area. Spells of pain usually last less than a few minutes.
The underlying cause is unclear. Some believe the pain may be from the chest wall or irritation of an intercostal nerve. Treatment is usually via reassurance, as the pain generally resolves without any specific treatment. Precordial catch syndrome is relatively common in children between the ages of 6 and 12 and is less common in adults. While in my twenties and thirties, I experienced a half dozen or so episodes.
Yesterday, while working on a ladder in the basement of the River House, I had a PCS event. Given the spotty cell service there and the proximity to Emerson Hospital, I decided to drive to the emergency room out of an abundance of caution. It has been more than thirty years since I last had an attack and I thought it better to be safe than sorry. I arrived in under 5 minutes and was immediately connected to an EKG monitor which showed no signs of heart anomalies and my pain had all but subsided. Much ado about nothing but interestingly, no one at the hospital suggested PCS as the cause and were intent on following up with a bunch of tests and x-rays that would have been pointless. While I truly appreciate being evaluated so quickly, once it became apparent that I was not having a heart issue minutes turned into hours while waiting for my blood work to come back. I eventually decided to disconnect myself from all the monitoring equipment and check myself out.
Our new home uses a Zehnder ERV (Energy Recovering Ventilation) system to provide continuous fresh air to the very tightly sealed building. Today, I installed the exterior intake and exhaust vents which look and act like nostrils. I then powered up the system for the first time. Everything worked as expected and the system self-test confirmed that the unit can deliver its maximum specified 600 cfm of airflow. At this rate, all the air in the house could be replaced with fresh air once every hour. The recommended rate of exchange is once every three hours so we will operate the system at 200 cfm.
Mount Mansfield is the highest mountain in Vermont with a summit that peaks at 4,393 feet (1,339 m) above sea level. Maya originally planned to do a solo ascent last weekend but was joined by Nicolai who saw an opportunity to train for his attempt to summit 18,996 Cayambe Volcano in Ecuador this fall. He will be making the climb to raise money for the Range of Motion Project (ROMP) whose mission is to ensure access to high-quality prosthetic care for underserved people, improving mobility and independence. Nico used the climb to shoot a fund-raising video with Maya as his videographer. Should you wish to support this cause you can use the link below to do so.
As planned, our new septic and pump chamber tanks were delivered and installed today. Offloading and placement of the tanks took less than 30 minutes, a testament to the careful preparation work. Since septic systems are based on gravity flow, any discrepancies in elevation will result in compromised function and must be corrected at this stage. Happily, the tank heights were perfect and the remainder of the day was spent connecting the tanks and beginning the backfill work.
Excavation for a new septic tank and pump chamber took place today at the River House. The addition of our attached garage forced us to relocate the existing ones because they no longer met the setback requirements. The tanks are due to arrive on site tomorrow and we are hoping to have the septic system operational by the end of the week. That leaves water as the last service we need to connect to the house. We may choose to put this off for some time since it will involve tearing up the driveway and we still have many trades coming and going on a daily basis.
One of my favorite things about living in Concord is that we have our own electric utility, the Concord Municipal Light Plant (CMLP). Today, the line crew above connected our new underground lines to the grid and we now have power throughout the house. All the folks at the CMLP are extremely customer focused and it is such a pleasure to work with them. Trying to get anything done with Comcast, Verizon, National Grid, or any other major utility by contrast is an exercise in total frustration. These guys arrived exactly when promised and 30 minutes later we had power to the house. 15 minutes later they had removed the overhead wires that have been providing temporary power for almost two years.
The bamboo plywood I am using to build the cabinetry for the River House is available in a natural or carbonized version. We selected the darker carbonized color for our project and I was befuddled when the first shipment arrived with a few sheets of natural mixed in with the carbonized. I even found two sheets that were natural on one side and carbonized on the other. Earlier this week, I received a make-up shipment to replace the product that was damaged during the initial delivery. To my dismay, the color did not remotely match the material I have been building with. I sent the company a detailed e-mail expressing my frustration and asking them to explain what was going on. They insisted that the replacement sheets were carbonized even though they looked like the natural version to my eye. Fast forward one day and I happened to turn over a sheet of plywood I was about to cut. The mystery was solved the instant I saw the outline of the hard core foam insulation slab that I used as a sacrificial base when cutting sheets with my track saw. It was apparent that the plywood changes color dramatically when exposed to air, presumably as moisture is absorbed.
Hardscaping for the River House will make extensive use of natural stones. Jeanine and I visited a stone yard yesterday where we reviewed the inventory and learned all about how large boulders are cut into slabs. Slabs can be 7 inches thick for stairs or 2-3 inches thick for patios. We will be using both types. Pictured below is the saw used to make the cuts. It is conceptually similar to a bandsaw except it is oriented horizontally and uses what looks like a rope instead of a band. The rope has diamond-impregnated beads every few inches.
I have been working on the new house 7 days a week for several months now. Today, I took the afternoon off to go stone shopping with Jeanine. Our patio area will feature some massive stone steps, all to be cut from a single ginormous boulder. It was very fun checking out all the possibilities and learning how the stone is cut. Later we joined friends on an evening birdwatching walk through Great Meadows. We were hoping to see Night Hawks but they never showed up. Instead, we were treated to a very beautiful Green Heron.
The pantry in our new house will feature open shelving from floor to ceiling on one side. In total, there will be six shelves, each 8ft long. Jeanine likes the look of thick shelves so I am laminating two pieces of plywood together faced with a 1/8″ thick veneer. Pictured here is a glue-up of three shelves at once.
The front door to our new house is sheltered by a small portico. Today we installed a single 5-1/4 thick slab of bluestone as the floor for that area. Working with a stone that weighs over a ton was no easy feat but in the end, it fit perfectly into the opening which was lined in a copper pan and sloped downward to shed water. Jeanine was on hand to film the installation which took about an hour in total. Our past homes have all incorporated smaller stones set in mortar which are much easier to install and significantly less expensive. Over time, however, the constant freeze-thaw cycles experienced during the winter lead to the failure of the joints. The slab we installed today should last for hundreds of years.
Last week the Flexzilla air hose I use with my portable compressor developed an internal bulge for no apparent reason I could ascertain. The hose, manufactured by Legacy Manufacturing, carries a 5-year warranty and naturally, I purchased it nearly 6 years ago. The fact is that I have used the hose more in the last month than since I acquired it. I decided to file a warranty claim given how little use the hose has seen and was pleasantly surprised when I received a prompt reply stating that they were sending me a replacement. This is an example of a company doing the right thing for its customers. They can now count on my business for life and I can highly recommend Legacy products to others.
Jeanine assisted me today as we installed 36 smart light switches throughout the River House. Each switch is a programmable dimmer with an occupancy sensor that can be accessed over the Wi-Fi network for home automation functions. She prepped them while I installed them which made the job go twice as fast as it would have had I been doing the work alone. Towards the end, the skin on my fingers was starting to blister from tightening so many twist-on wire nuts (4 per switch) and she took over that job as well. Next, I taught her how to apply the hard wax oil we will be using on all the cabinetry and she finished one of the panels that will surround our freezer. We wrapped up the day by making a catalog containing the QR code for each light switch to facilitate future programming once we have Wi-Fi enabled. It is really the first time we have worked on the new house together and I really enjoyed working with her.
Jeanine returned today from a week-long visit with her sister Susan who lives in Burlington, Vermont. They had all kinds of fun including a visit to the Happy Bird Poultry Farm. I have been so busy working on the River House that time has passed quickly. Even so, I missed her and am glad she is back. I guess that would make me the happy bird.
Kyle shared this photo of his blender which was not up to the task of making his morning smoothie. Fortunately, the company has offered to replace it for free.
I completed the tall kitchen cabinet carcass for the double oven today. So far it has been the most time-consuming to build. All but one of the front faces required veneering, the “shelf” which supports the ovens had to be designed to support a 350-pound load, and the cavity had to be dead plumb, level, and square. It is also the heaviest single item I have built so far which made it difficult to move and install. There will be a drawer below the ovens and a cabinet with two doors above it. Still needed is a filler strip on the left to close the gap to the wall which is one of the few in the entire house that is not perfectly plumb; argh. Even though it fought me almost every step of the way, I am extremely happy with the finished product.
It is said that woodworkers basically take big pieces of wood, cut them into smaller pieces, and then glue them back together. Therefore, if you want to make fine things out of wood you need to master the art of gluing. Apply too little and your joint will fail. Apply too much and you will have a time-consuming gooey mess to clean up. After 40 years of practice, I am prepared to say that the glue lines pictured above are as close to perfection as you can get. You are actually looking at two plywood panels, each with a 1/8″ veneer glued to the edge. The veneers are placed back to back and the pair of panels are clamped together as cauls for each other. If you apply exactly the right amount of glue, distribute it evenly, and apply uniform clamping pressure you will be rewarded with the tiniest bead of squeeze-out confirming full coverage. The shims placed under the bar clamps keep them out of the glue preventing rusting of the clamps and staining of the wood.
I completed the base for the kitchen island today. When the countertop is added it will create a seating area on one side and have the induction cooktop placed on the other. Unlike the other cabinets in the kitchen, the island will sit on top of the finished floor. Therefore, I have not yet fastened the end caps or the back panel to the drawer carcass to keep the weight manageable; it would be very difficult to move fully assembled. The end cap on the kitchen-facing side includes open shelving for frequently used spices and cooking oils. Should we be so lucky to entertain toddlers at some point, I am sure this will be a favorite point of interest and I already have some child-proofing ideas in mind.
We deliberately pulled our electrical permit in the final week of 2022 so that we would not be subject to new 2023 code requirements that do not allow for kitchen island-mounted outlets. The new regulations only allow for outlets mounted on island countertops which is the last place I would pick to put an outlet, pop-up, or otherwise. The outlet within the seating area will include 2 USB-C charging ports and will not be visible from the dining and living areas. The other outlet will be for cooking-related appliances that are temporarily used on the island.
With these choices, we have a single island with two personalities. Viewed from the dining/living space, it presents clean lines and no clutter. while the kitchen end is all about the business of cooking.
If sawdust production is any measure of my cabinet making progress, I am 30 gallons in, closer to 50 if you include the contents of my dust collection system bin. Most of this was generated from my router table while machining lock miter joints. It is the only major piece of equipment I have that is not yet connected to my dust collector. I plan to rectify this before doing any further routing and hope to have the necessary parts within the week.
The kids joined us at the Road House for dinner to celebrate Kyle’s 31st birthday. Jeanine cooked up a feast including a peach-tomato-basil salad, fresh corn risotto, and beef tips. Maya was here for most of the day doing upkeep on her tiny house which she was proud to show off after dinner. I spent most of the day at the River House continuing with cabinetry work. Busy schedules have prevented us from gathering as a family for several weeks and it was nice to catch up with everyone. Kyle has been promised a promotion to manager within the year at his job and is now renting out his basement to a couple and their two puppies. He is planning to take a week-long vacation in Montana after attending a wedding there. Nico is in training for his upcoming climb of the 19,000 ft Cayambe Volcano in Ecuador and for the Amp Futbol Cup in Warsaw, Poland as a member of the US National Team. Maya will be climbing in Vermont next weekend and is planning a trip to Olympic National Park later this month. The shoulder injury she sustained mountain biking will require arthroscopic surgery and she is looking into the best options for having that procedure.
This website is dedicated to sharing, with family and friends, the day-to-day adventures of the Calabria family.
