I installed three out of seven Newell posts today. More accurately, I installed three-quarters of each post. I have left one side open so that I can secure the railings with a bolt driven from the inside. Tomorrow, I will glue on the missing face and top cap. The base is glued to a cleat that is the same size as the inside of the hollow post. The cleat is secured to the floor with a massive lag screw. If tomorrow goes smoothly, I should be finished with the railings by the end of Monday and we will then be ready for our certificte of occupancy inspection. Fingers crossed.

Thanks to our neighborhood list server, I was alerted to the approach of a bevy of swans, 13 in total. I was able to grab my good camera and photograph them as they swam past the house. Ice has begun to form near the banks but the bulk of the river is still flowing. If I had to guess, I would say they were having a leisurely swim, resting from what was likely several hundred miles of flying. Jeanine arrived at the house shortly after they passed by on the water but spotted them in the air as they resumed their migration.

I completed the last three railings for the staircase today by machining the holes needed to connect and secure the balusters to the rail. The anatomy of the rail is pictured below. The balusters are slid over the connector to mate with the rail at an angle of 32.5 degrees. The ends of the rails have a threaded metal insert that will accept a fastener to secure it to the Newell posts. One end of the rail has a 16.25 degree compound joint followed by a mitered right angle return. The rail itself was made by laminating non-overlapping 4 foot long sections of bamboo plywood together (for a perfect match to the stair treads).

Although my college degrees are in Electrical Engineering, it is only because the field of Computer Engineering was in its infancy. My primary concentration was in logic design and computer architecture. Even the most advanced computers today are still based on the same basic building blocks that perform the logical operations of AND, OR, and NOT. When I was in grade school, these logic elements were constructed out of individual transistors. By the time I was in high school, they had become available on integrated circuits that offered multiple gates, shift registers, flip-flops, multiplexors, and a bunch of other more sophisticated functions. Pictured above is the collection of chips I assembled while in college so that I could quickly prototype my ideas. My first self directed design was a 16-channel logic analyzer which won me the Stearn’s Prize awarded to the outstanding student in electrical or computer engineering at Union College.

Alas, It has been more than three decades since I built anything from these parts and I decided that they would not be making the move to the River House. Jeanine and I are making a concerted effort to get rid of all of the things we have accumulated over the years but no longer use.

Today, I decided to make a timelapse video of a typical day in the shop. Unfortunately, or fortunately depending on your perspective, my camera ran out of both storage space and battery so only two hours were captured. The video lasts less than 2 minutes and shows the construction of seven Newell posts. Order of operations: Rip boards to 3-inch width, cut to length at the miter saw, move to the router table to create a lock miter joint along all edges (most time-consuming), return to the table saw to make relief cut in half the boards to prevent tearout, empty the dust collector at some point, dry fit the Newell posts and move on to routing and sanding the hand rail I glued up earlier in the day. Not shown, the other 6 hours of work before returning home to snow blow the driveway. Gotta love retirement?

Shoptimization continued today. First, I moved my tablesaw and jointer/planer 6 inches to the east. This small change permits me to machine 10-foot long stock which was not possible before. Second, I built a set of shelves for my cordless tools that are now located under the picture window. Moving them from their previous location also opens up the space where I plan to install a sink one day. Third, I consolidate all my tools on the north wall of the shop where they are close at hand to my assembly tables. Fourth, I located my drill press on the east wall and repurposed a portable shelving unit I made for my old shop for drill bits and accesories. When all was said and done, I moved every last thing in my shop except the bandsaw and miter saw. I am very happy with the final layout and do not plan to make any future changes.

The remaining bamboo plywood needed to complete the stair railing for the River House is scheduled to arrive tomorrow and I found myself with a free day. I decided to spend the time optimizing my shop, a process I call “shoptimization.” With six months under my belt, I had a very clear plan for the changes I wanted to make. First, I moved my router table to where the drill press used to be. I aligned the table height with that of the miter saw to take advantage of a free outfeed table. Second, I moved my “harware store” (small part cabinets with all manner of screws, nuts and bolts, etc.) from the north wall to the south wall. This freed up some prime real estate where I will locate more frequently accessed tools. Third, I moved my sanding station from next to the outside door to the corner where the router table used to be. This location allows me better access to the machine and is already plumbed for dust collection. Tomorrow, I will figure out where to locate the displaced drill press.

Pictured above are the angled ends of two 8-foot-long handrails. the first joint takes the diagonal rail back to horizontal and the second turns 90 degrees to mate with the Newell post. Each rail has 20 recessed holes on the underside angled at 32.5 degrees where the baluster will be situated. Each recess has a smaller and deeper hole drilled in the center where a 3D-printed baluster connector will be fastened with a screw. In total, each rail requires more than 60 machining operations and a dozen glue ups. A single mistake can render the entire rail unusable which makes for very stressful work. Fortunatley, these two rails came out perfectly and today they were treated to two coats of sealer and two of a protective finish. During the 2 hours of drying time between each coat, I installed a new fence on my table saw. I ordered the device back in September and have been patiently anticipating its arrival. All I can say, is that it was worth the wait and every penny I paid for it. I then cut down and fitted the original fence to my bandsaw and scrapping the piece of crap it was supplied with.

With all the work I have been doing on the River House, I have had little time for dedicated photography. The arrival of a small group of migrating common mergansers and a relatively warm day was the only motivation I needed to take a brief pause to spend some time outdoors with my camera.

Jeanine presented me with an odd request today. She wanted me to drill a couple of holes through the edges of a pair of sea shells so she could sew them onto a garment. I am sure there is a way to do this without destroying the shells in the process but I decided it would be far easier to glue a couple of loops to the back through which the thread could be passed. Jeanine was in charge of fabricating a superhero-themed outfit for “Island Woman”, one of her friends who is celebrating her 60th birthday.

Even though it was explained to me, I remain unclear about why Jeanine is dressed as Fanny Wheeler, an important figure in Concord’s history. Something about a secret society.

I was dressed as a stair railing contractor and completed 5 of the 7 railings needed to apply for our occupancy permit. I am using 3D-printed parts to connect the railing to the balusters. These can be seen in the photo below where the railing is turned upside down with the printed parts screwed into the bottom of the railing.

Only another soccer player can fully appreciate the amazing goal that Nico scored during a match against rival New York recently. The degree of difficulty of this shot is off the charts! (a) It is a one-touch strike on a moving ball, (b) it is taken from a great distance, (c) it is placed just inside the post. Nico has scored some truly amazing goals throughout his career but for me, this may be his best. Using the known length of his crutch as a measurement reference, I estimate this shot was taken at a distance from goal of 64 feet. Keep in mind that amputee soccer goals are smaller than standard ones measuring only 7’x16′. Compare Nico’s strike to Stephen Gerrard’s famous equivalent. I think any professional footballer would be envious of Nico’s banger.

I couldn’t resist a second post featuring our first snow of the season. Today, blue skies and sunshine replaced the gray and cloudy skies of yesterday. The forecast is calling for rain tomorrow so this winter wonderland landscape will soon be gone. This photo of the Sudbury River is about a quarter of a mile downstream from our new home and the bridge is one we cross daily to go almost anywhere.

Thus far, this winter has been quite mild. Today, we got our first proper snowfall, a total of about 9 inches which started during the night and fell throughout most of the day. I took these drone photos about one-third of the way through the storm during a lull. Jeanine and I spent the entire day at the River House working on the stair railings. We made reasonable progress despite a few minor setbacks.

With Jeanine assisting me all day, we made excellent progress on setting balusters in place on the stairs from the first to the second floor. Weather permitting, we hope to do the same for the stairs to the basement tomorrow. A snowstorm is currently forecasted to dump half a foot of snow on us throughout the day. The work goes slowly because of the need for accuracy and the high cost of even a small mistake. While the balusters are being installed permanently, all the newell posts and rails are temporary and will need to be replaced when the bamboo needed for their construction finally arrives.

The first of two episodes on the Build Show featuring our River House project dropped today. In it, our architect, Steve Baczek discusses aspects of the design with host Matt Risinger.

Last week, FedEx attempted to deliver two pallets of plywood that I ordered weeks ago. The first pallet was as ordered. The second contained long boxes and not the 4’x8′ sheet goods I was expecting. I accepted the first pallet and rejected the second. Naturally, the missing plywood is what I need to complete the stair railings. The supplier acknowledged the error and is shipping out the correct material but it will probably take several weeks for that to arrive. Since our occupancy permit is gated by the completion of the stair railing, I have opted to proceed using scrap plywood that I will later replace with bamboo. This morning, I built and installed 7 temporary newell posts (three visible in the photo, the remainder are on the floors above and below). I then installed all the balusters for the guard rails on a spacer rail that will hold them in the correct position until I can epoxy them to the lag screw studs in the floor. Once cured, I will replace the spacer rail with a temporary code compliant railing. Next, I will repeat the process for the stair hand rails. On a positive note, I really like the shadow pattern generated by the balusters.

Nico was recently featured in an AdaptX podcast interview. The extensive conversation is centered on the work he is doing with the Bionic Project as well as his crusade to build a world-class amputee soccer program in the US. I am extremely proud of the work he is doing and how eloquently he speaks about it. If you can set aside an hour to listen to the full interview, I promise you will learn some things that will change your perspective regarding people with a disability.

With the holidays in the rearview mirror, it was time to get back to work on the River House. I used an abrasive cutoff disc in my grinder to remove the heads of ~150 half-inch lag screws. It was not a pleasant task. I had to wear a respirator, protective goggles, and hearing protection for my safety and used the galvanized steel jig below to protect the stairs and floors from the spark generated by the grinding process. It took me about a minute to decapitate each screw which translates to about 2 1/2 hours bent over with a heavy grinder. Jeanine was kind enough to give me a back rub that helped alleviate the pain. I also began to erect the temporary scaffolding that will hold the balusters in place while they are glued to the studs on the floor.

Last night, Jeanine and I spent New Year’s Eve with Kyle and his girlfriend Heloisa at the River House. We spent a good deal of time outside before and after dinner gathered around our new fire pit for its inaugural use. Kyle prepared a smoked brisket which we had for dinner and a second time today when the boys came over to watch Premier League Soccer (Liverpool vs Manchester United) on the big screen. Kyle is well on his way to becoming a grill master and we are fortunate to be the beneficiaries of his growing passion for the art.

It is fitting that on this last day of a year full of construction, I would be working on the last project standing in the way of getting our occupancy permit for the new house. The railing system for our stairs will use three vertical balusters per stair tread. These hollow steel tubes will be epoxied to the lag screws which I installed today but not until after I cut the heads off. I have opted for epoxy over an earlier idea I had since it will be stronger and offer more latitude for adjusting perpendicularity. In total, I installed just shy of 150 screws. Each one had to be perfectly positioned and driven in plumb. To accomplish this I built several jigs to ensure repeatability and accuracy.

Answer to yesterday’s puzzle: The bird sitting on the top shelf to the right of center.

Something in this photo which I took while shopping at Home Depot does not belong. See if you can figure it out. The answer will appear at the very bottom of tomorrow’s post.

Located at the back of the River House walk-in pantry is a column-style freezer that until today lacked a matching bamboo panel for the door. It was the last component needed to 100% complete the kitchen. Even though Jeanine originally wanted a push-to-open capability for the refrigerator and freezer she has since decided she would prefer a traditional handle and requested that it be made of bamboo to match everything else. Her wish was my command.

I rarely, if ever, post photographs that are not mine or ones taken by family members. Today, I encountered an image that was so perfectly executed that I felt compelled to share it. I was not able to ascertain the photographer but it was originally posted on a yoga studio Instagram page. Kudos to the photographer and model. Perhaps, my interest in this photo is a sign that I am ready for a beach vacation after months of work on the new house. I am confident it is not a sign that I should take up yoga any time soon.

After more than 2 months of waiting, the additional bamboo plywood needed to continue built-in construction at the River House finally arrived. I cut all the panels needed to complete the drawer fronts and cabinet doors for the laundry, mudroom, and shop and the front panel for the flush-mounted freezer in the pantry. Jeanine and Susan worked together to apply finish to some two dozen panels leaving them ready for installation. I also started replacing the temporary stairs from the back hall to the garage with the final design that includes provisions for a future wheelchair ramp should that ever be needed. An additional shipment of plywood for the indoor stair railing is scheduled to arrive tomorrow, weather permitting. With any luck, we will be ready for our occupancy inspection during the first week of the new year.

For many years now we have been doing a Secret Santa gift exchange. Everyone in our immediate family group is randomly and secretly assigned someone else in the group for whom to purchase a gift(s). Rather than shopping for everyone in the family, you only need to focus on one person. This year, Nico was my Secret Santa and he got me a super sweet Arctyrex jacket among other smaller items. Since I have been an exceptionally good boy this year, I decided that I would also give myself a gift. When I saw this miter gauge go on sale for 50% off I could not resist the temptation. When it arrived the day before Christmas, I decided to leave it in the box and put it under the tree with a Secret Santa label addressed to me. It took the family about 2 seconds to figure out what was going on. It is said that it is better to give than to receive. I am prepared to assert that it is even more satisfying to do both at the same time.

Jeanine and I spent the night sleeping at the River House so that there would be enough beds at the Road House for all the guests we have this year. We woke up to fog on the river and swans swimming downstream. Even though there were only four of the famed 7 swans a’ swimming, it felt like a true blessing.

Fiona, one of Maya’s roommates and high school friend is staying with us over the Christmas holiday. Work prevented her from joining her parents who are celebrating in England. Also visiting us is Jeanine’s sister, Susan who we always look forward to spending the holidays with. This evening we gathered at the River House where we enjoyed raclette, a Swiss dish, also popular in other Alpine countries, based on heating cheese and scraping off the melted part onto boiled potatoes and sausages. Maya created a Bouche de Noël for dessert complete with woodland decorations (my favorite are the mushrooms). We also enjoyed fine chocolates, a gift from Nicolai’s girlfriend Samantha and her dog.

I have never thought of my sister Alissa as much of a cook. Recently, however, she has become much more adventurous in the kitchen and I am considering updating my assessment of her culinary talents. However, such will not be done until I have had a chance to sample the goods. Hint: This could be facilitated by a small overnight care package.

Before we can get our certificate of occupancy for the River House, we need to have stair railings, final or temporary in place for the interior and exterior stairs. Today I completed temporary railings for the front door steps and patio steps. These will eventually be fabricated in stainless steel, work best done in warm weather, and after the steps have had plenty of time to settle into their final positions. I was able to secure the front stair railings into the stone using anchor bolts which will not be visible when they are eventually removed. For the patio stairs, I chose to use 5-gallon pails filled with 100 pounds of concrete for bases rather than drilling holes which will be visible later.

Jeanine, Maya, Samantha, and I attended the end-of-the-year party/amputee soccer clinic/Amputee Revs soccer practice this evening in Marlborough. Children were given an opportunity to play soccer on crutches to gain an appreciation for the challenges faced by those with limb differences. They did warmup drills followed by a match. Eventually, those who did not need them, shed their crutches and play morphed into a practice session for Nico’s soccer team.